Volt Exciter
Check out this page if you are looking for Volt Exciter
 |
 TWO 2 BSW SOUND PROJECTOR EXCITER LAMP BULB 7 VOLTS 02 AMP GUARENTEED NIB  US $10.00
|
 Kelmar Systems Inc Exciter Lamp Supply 7402 B ATL US $39.50
|
 BRK 4v 3w Eiki 16mm Sound Exciter Reproducer Lamp Bulb US $12.00
|
 BAK Exciter Lamp Bulb Apollo 4 Volt 75 Amp NEW US $10.00
|
 BAK BRS SOUND PROJECTOR EXCITER LAMP BULB 4 VOLTS 075 AMP GUARENTEED NIB US $5.00
|
 BFX Made in USA 4 v Exciter Sound Reproducer KODAK Kodascope Lamp Bulb Free Ship US $18.00
|
 BFX AMERICAN Made 4 v Exciter Sound Reproducer Bolex Light Lamp Bulb Free Ship US $18.00
|
 BFT Exciter Sound Reproducer Lamp GE US $12.00
|
 NOS RADIANT BAC EXCITER BULBS 4VOLT 75AMP 20 US $31.95
|
 KODAK PAGEANT 6 v 6 w 1 a Sound Exciter Lamp 16mm Projector Bulb x1 Free Ship US $12.00
|
 64553 HLX BOLEX 421 510 521 16mm 250 w 24 v Movie Projector Lamp Bulb Free Ship US $24.00
|
 7 v 3 w Ampro Singer 16mm Movie Sound Exciter Reproducer American Lamp Free Ship US $12.00
|
 BSK KODAK PAGEANT 6 v 6 w Sound Lamp 16mm Projector Bulb AMERICAN Free Ship US $12.00
|
 ELC Eiki BH ELMO 16mm Movie Sound Projector Lamp Bulb US $22.00
|
 Ampro Eiki 16mm Movie Sound Exciter Reproducer 4 v Lamp US $14.00
|
 Exciter Lamp BXR US $15.00
|
 10 NEW SYLVANIA BAK EXCITER LAMP BULBS MOVIE PROJECTOR SOUND REPRODUCTION US $19.99
|
 20 NEW SYLVANIA BRK EXCITER LAMP BULBS MOVIE PROJECTOR SOUND REPRODUCTION US $29.99
|
 10 NEW SYLVANIA BGB EXCITER LAMP BULBS MOVIE PROJECTOR SOUND REPRODUCTION US $24.99
|
 KONDO BRK KE 040 4VOLT 075 AMP EXCITER LIGHT BULB NEW US $12.99
|
 6 v 6 w AMERICAN mfg Sound Reproducer Exciter Projector Lamp Bulb x1 Free Ship US $12.00
|
 Made in USA by GE ELC Eiki BH ELMO 16mm Movie Sound Projector Lamp Free Ship US $24.00
|
 EIKI 16MM 2KW XENON PROJECTOR 9120 OPT MAG SND Intermittent Type US $9,500.00
|
 1A T5 6 v 6 w KODAK JAN EXCITER Sound Lamp 8 16mm Projector Bulb x1 Free Ship US $13.00
|
 Vintage Projection Lamps Bulbs BRS New US $8.00
|
 13 BSW Light Bulb Box Radiant Lamps Exciter 7 amp 15 Volt C8 Filiment NOS US $19.99
|
On a large generator powered by a 6cyl. john dear diesel What would make the exciter rotor banding come loose?
I recently seperated the generator from the engine and replaced the rear main oil seal on the engine the electric generator was only moved back about 16-18 inches to access rear main seal. job went well with no problems after completeing job I turned down rpms to about 1000 rpm It was put back in service They use it to power up refer containers from the harbor. the next day I check it and they had turned up rpms to ??? as fast as it would run and 12 refer units running off it oh it's 480 volt well it ran for a week non stop and broke down and of corse it was my fault all i did was unbolt drive plate on front of rotor from flywheel of engine ..est to repair is 6,000 could this be my fault after it ran for a week or caused from hi rpms and heat related possibley
A little more information would be helpful as to the size and model of generator. Is it possible the repair shop could give you more detailed explanation as to exactly what they believe happened?
Is this a single bearing or two bearing generator? If it has only one bearing and the shaft is supported by the engine flywheel on the engine end, then the postion and shimming of the engine and generator may be critical to keep the rotor centered between the stator poles. These clearances are very small and they could have been rubbing if not aligned. On small single bearing types, the housings are made to fit together in perfect alignment, and can not be misaligned to avoid this problem. On larger units, this matched housing arrangement may not be possible.
A generator with a bearing at each end of it's shaft is less likely to have this problem of rotor alingment, It would have a problem with coupling or bearing failures if not properly aligned with the engine. This link may help explain. http://www.cumminsgeneratortechnologies.com/www/en/common/pdfs/manuals/bc/TD_BC%20MAN%20GB_01_10_Rev04.pdf
Comments